How to Use Bonding Plaster: A Practical Guide for Plasterers

Bonding plaster is one of those materials that can make a plastering job much easier when it’s used on the right background. It is mainly used as an undercoat, giving the finishing plaster a suitable base to adhere to. But getting good results isn’t simply a case of mixing the powder with water and putting it on the wall.

The background, mix, thickness and timing all matter. If any of these are wrong, you can end up with cracks, poor adhesion or a finish that becomes difficult to skim.

So, if you’re wondering how to use bonding plaster, it helps to understand what the material is actually designed to do before picking up your trowel.

What Is Bonding Plaster Used For?

Bonding plaster is a gypsum-based undercoat designed particularly for smooth or low-suction traditional undercoat plasters to grip properly. British Gypsum describes Thistle BondingCoat as a backing plaster for smooth or low-suction backgrounds, including suitable new walls and areas being repaired before skimming.

So, what is bonding plaster used for in practical terms? It can be used on suitable concrete, some brick and blockwork, plasterboard and other backgrounds where the manufacturer’s system recommends it. The exact substrate matters, though. You shouldn’t assume that every wall needs bonding plaster simply because you’re planning to skim it.

That’s one of the first things worth checking before starting.

Check the Background Before Mixing

A good plastering job starts before the plaster is mixed.

The surface should be clean, dry and free from dust, oil, loose material and other contaminants. Concrete backgrounds may need particular preparation, and very smooth or low-suction surfaces may require a separate bonding agent rather than bonding plaster alone. British Gypsum recommends checking its plaster selector guidance to confirm that the chosen product is suitable for the background.

This is where people sometimes get caught out. A wall can look perfectly fine but still provide a poor base for plaster. If the substrate is unsuitable, getting the application technique right won’t solve the underlying problem.

Remove anything loose, deal with obvious surface defects and make sure the background is ready before you start mixing.

How to Use Bonding Plaster Correctly

Once the background is ready, the next step is mixing. Always follow the instructions for the particular product you’re using because water requirements & working times can vary.

For example, British Gypsum’s current Thistle BondingCoat guidance recommends approximately 14 litres of clean water for a 25kg bag. The plaster is added gradually while mixing, and excessive mechanical mixing should be avoided.

Don’t guess the water quantity by eye. A mix that’s too wet can become difficult to control, while adding too little water can make it stiff & unpleasant to spread.

When the mix is ready, apply it firmly to the prepared background. For Thistle BondingCoat, the recommended application thickness is 11mm, with 8mm specified on plasterboard and ceilings.

The important point is to follow the product instructions rather than trying to build up a thick layer in one go.

Getting the Surface Ready for the Finish Coat

Bonding plaster isn’t normally the final decorative surface. Its job is to provide the base for the finishing plaster.

As the bonding coat begins to firm up, the surface needs to be keyed so that the next coat has something to grip. British Gypsum’s installation guidance recommends rubbing up the surface with a devil float as the plaster firms, before applying a suitable finishing plaster.

This stage is easy to overlook if you’re concentrating on getting the wall flat. A perfectly smooth bonding coat isn’t necessarily what you want. The surface needs the appropriate texture for the finishing system you’re using.

Timing matters here too. Don’t leave the preparation until the bonding coat has completely hardened if the manufacturer’s instructions require the key to be formed while the plaster is firming.

Don’t Keep Adding Thickness to One Coat

Sometimes a wall is so uneven that a single application isn’t enough. That’s when you need to resist the temptation to simply pile more plaster onto the same coat.

British Gypsum advises that thicknesses above 11mm should be built up in a series of fully keyed coats, subject to the suitability of the background. Each new layer should use a fresh mix and be applied after the previous coat has firmed up.

This approach takes a little longer, but it gives you much better control over the finished surface.

Trying to correct a badly uneven wall by applying one excessively thick coat can create problems later. The plaster needs to be applied within the limits recommended for the particular product & background.

Common Mistakes to Avoid

One of the most common mistakes is choosing bonding plaster simply because it’s available. It isn’t a universal undercoat. The background should always be checked first.

Another mistake is getting the mix wrong. Too much water can leave you fighting the material instead of controlling it, while a mix that’s too stiff can make application unnecessarily hard.

Rushing the keying stage is another problem. The surface needs to be prepared at the right point in the setting process, not after you’ve left it until the following day.

It’s also worth remembering that setting times aren’t fixed to the minute. British Gypsum gives approximate timings & notes that background suction & conditions such as cold weather can affect finishing times.

Bonding Plaster or Bonding Agent?

The names can cause confusion, particularly because products such as Thistle BondingCoat and Thistle Bond-it sound very similar.

They aren’t the same thing. BondingCoat is a gypsum backing plaster, while Bond-it is a bonding agent used to improve the key on certain backgrounds before plastering. British Gypsum states that Bond-it is used internally where a background requires an improved key and should be allowed to dry for at least 24 hours before plaster is applied.

Choosing between them depends on the background and the plastering system you’re using. Don’t substitute one for the other simply because both products contain the word “bonding”.

A Better Finish Starts With Preparation

Learning how to use bonding plaster is really about more than knowing how to spread it across a wall. The preparation underneath, the correct mix, suitable thickness & timing of the key all have a direct effect on what happens with the finishing coat.

And that’s really the useful answer to what is bonding plaster used for: it’s a base coat for suitable backgrounds where you need the right surface for the next stage of plastering.

Before mixing, spend a few more minutes reviewing the substrate and product instructions. When attempting to obtain a clean, even finish later, that little bit of preparation may save a significant amount of time.

Stay in the Loop

Get the daily email from CryptoNews that makes reading the news actually enjoyable. Join our mailing list to stay in the loop to stay informed, for free.

Latest stories

- Advertisement - spot_img

You might also like...